|
Post by [S.O.A.R] William on Aug 16, 2006 23:12:34 GMT 7
Hmmm, Mga sir, meka encounter kung meju ka wirduhan ketang R6 ku... Kasi, after doing some paint job at inassemble ko na ulit siya, I've tried my battery tas dba hindi siya umandar? Tas nag change ako ng battery... Tas ok na... Well, here's what happen lately... I've tried to test fire my R6 kaninang umaga with the new battery. And to my surprise, hindi nanaman siya nag fire. So isip isip ako... Hindi ko naman pinakyalaman yung Gearbox. Actually, inalis ko lang yung gearbox for the paint job. Tas naisip ko naman na try ko ilabas ang motor. Just in case baka mapa ikot ko siya with my batteries since wala na siyang kina-crank na spring. So nung nakalabas na, tas ni-connect ko na yung mga wires, hindi nag react yung motor! Thinking that the battery may have totally run out of charge, sinaksak ko ito dun sa MP5 tas yun, pumutok yung MP5. Then tried it on my R6's motor again and still, no response... Isip na ako ng isip until na i-sipan ko na tanggalin ko yung fuse then ibalik ko ulit. Tas yun, nag ok na siya. Hanggang ngayun ok na. Ewan ko lang bukas or sa sunday pero may nakita akong improvements nung ginalaw ko yung fuse. Anong comment niyo mga sir? May naka experience na ba sa inyo ng "occasional-non-functioning-motor"? Ano pa ba kayang possible source ng hindi pag-function ng motor ng R6 ko? Salamatz!
|
|
SNIPERACE
Global Moderator
Violence is the first refuge of the incompetent.
Posts: 1,209
|
Post by SNIPERACE on Aug 17, 2006 0:46:25 GMT 7
wirings sir talaga maging cause nun. it sometimes happens, but dont worry madali naman makita problem especially with a tester/amp meter
|
|
rambo
Corps Commander
Posts: 674
|
Post by rambo on Aug 17, 2006 8:42:42 GMT 7
sa kakaisip naging esep esep LOL! well atleast nakita mo agad yung problema. loose contacts lang sa fuse.
kakainis tlga yung ganyan yung alang power tlga. kaya maganda tlga may tester ka.
so heto mga culprit as far my experience goes when it comes to a dead gun... - loose contacts on fuse - mis align due to heat or burned out contact points on switch assembly - loose soldered connections - loose connectors *hmmmmmmm.....sumakit bigla tyan ko CR ku pa...
|
|
rambo
Corps Commander
Posts: 674
|
Post by rambo on Aug 17, 2006 8:59:15 GMT 7
yung wire's na ginamit sa r6 are good enough which are basically heat resistant AW16 ata.
pag nakabili na ko ng lipoly na kasya dun sa foregrip hehe bili na rin ng deepfire piston body at sp130 hehe para magamit ko uli sa hi-end games. mga next week na siguro yun. medyo miss ko na rin yung naka m4 sa games.
|
|
|
Post by [S.O.A.R] William on Aug 17, 2006 9:37:34 GMT 7
Hhmm, I was thinking sir nung makananu ya meh loose itang connection sa fuse. Tas now mejo parang alam ko na...
Kasi nung ni-disassemble ko yung R6 ku, siyempre natural lang na aalisin ko na yung mga plastic na nag-lo-lock dun sa fuse case. Yung mga parang maliit na belt na ginagamit sa mga wire brakes ng mga bike pra organized sila.
Tas nung assemble ko na ulit, hindi ko na binigyan ng lock yung fuse case. Kumbaga, naka "bitin" siya. gumagalaw galaw... Kaya siguro nagkaroon ng loose.
Pero sana dun na nga ang culprit...
So far, I've tested it ulit this morning... Still alive nad kickin'! Weheheeh!
Tig magkano ba ang mga amp tester na yan? Pra makabili ako.. Bili na rin siguro ako ng mga soldering equipments pra completo na mga tools ko pang opera ng R6.. ;D
|
|
SNIPERACE
Global Moderator
Violence is the first refuge of the incompetent.
Posts: 1,209
|
Post by SNIPERACE on Aug 17, 2006 12:29:30 GMT 7
mura lang sir will. yakang yaka mo yan hehe. and besides you can use it naman around the house when the time comes.
|
|
|
Post by [S.O.A.R] William on Aug 17, 2006 14:19:20 GMT 7
Oki sir, bukas siguro, after ng class ko, try ko maghanap-hanap.
Sir question pa pla, na-mention dito yung "burned contact points". If this is the case, how can I fix that? Pede ba siya ma fix ng as-is or may kailangan pang bilhin na replacement parts?
|
|
SNIPERACE
Global Moderator
Violence is the first refuge of the incompetent.
Posts: 1,209
|
Post by SNIPERACE on Aug 17, 2006 15:08:50 GMT 7
marami paraan. some would buy new ones, some would place new bronze contacts, etc. depende sa gusto mo gawin. lol
|
|
|
Post by [S.O.A.R] William on Aug 17, 2006 15:44:21 GMT 7
Okidoki. Salamatz!
|
|
rambo
Corps Commander
Posts: 674
|
Post by rambo on Aug 17, 2006 19:56:12 GMT 7
add ko lang para keng sese tamu...LOL! avoid firing too much semi's kasi parang nagwe-welding yung mga contacts mu non which will cost burned contacts unless may relay kana kahit buung hapon ka mag semi ok na kasi ala na daw spark nun. hopefully totoo nga yun kasi di kupa nainstallan.
|
|
SNIPERACE
Global Moderator
Violence is the first refuge of the incompetent.
Posts: 1,209
|
Post by SNIPERACE on Aug 18, 2006 16:34:03 GMT 7
add ko lang para keng sese tamu...LOL! avoid firing too much semi's kasi parang nagwe-welding yung mga contacts mu non which will cost burned contacts unless may relay kana kahit buung hapon ka mag semi ok na kasi ala na daw spark nun. hopefully totoo nga yun kasi di kupa nainstallan. ang hirap maghanap ng maliit na relay sir.
|
|
rambo
Corps Commander
Posts: 674
|
Post by rambo on Aug 18, 2006 18:57:30 GMT 7
i see. yung mosfet naman kaya?
|
|
SNIPERACE
Global Moderator
Violence is the first refuge of the incompetent.
Posts: 1,209
|
Post by SNIPERACE on Aug 18, 2006 22:10:09 GMT 7
mikakapali la kanu e
|
|
rambo
Corps Commander
Posts: 674
|
Post by rambo on Aug 18, 2006 23:02:55 GMT 7
wapin kanu. potang akit ke tng kakilala kung mekaniku try ku papantun kayang malating relay.
|
|
Mr.S
Moderator
קלע סער
Posts: 672
|
Post by Mr.S on Aug 19, 2006 17:20:07 GMT 7
No need for a gunsmith when sir Sniperace and sir Mezner are in the house!
|
|